PIC24F16KA101 UART PROBLEM (Kinimod)
Hello, I'm not very experienced with PIC and I'm having trouble with setting up my UART. I'm trying to program a pic24f16ka101 using picit3 and code seems to work perfectly on a debugging mode. When it...
View ArticlePIC24FJ128GA202 Deep Sleep issue (TTForum)
Hello all, I am attempting to use the deep sleep functionality of the PIC24FJ128GA202 microcontroller. In testing I appear to be switching the device into one sleep mode or another. However I am not...
View ArticlePIC24FJ64GB002 PWM question (Alanwms)
I have noticed that the output of the PWM still runs when changing the duty cycle to zero. It looks like a zero equates to 1. There is a very small pulse at duty cycle value of zero. That pulse is the...
View ArticlePIC24FJ64GU205 & pickit3 (microchipuser59000)
Hello, Why can't i see connected hardware tool PICkit3 with PIC24FJ64GU205 ? Thanks..
View Article[SCCP] CCPIF interrupt does not rise in single edge output high compare mode...
Hello I'm using the SCCP7 module in a PIC24FJ512GA610. I don't need to use an output pin, I only need to get the CCP7 interrupt when compares matches (CCP7TMRL with CCP7RAL), and a second CCT7...
View Article[MCCP] In output compare mode, spurious CCPIF trigger when ICM pin toggle...
Hello, I encountered a strange problem when mixing UART4 and SCCP7 use on PIC24FJ512GA610.The SCCP7 is configured in single compare low output mode, the output pin is disabled, I only need to have the...
View ArticleDual partition, upgrade and FBTSEQ and configuration bits change. (rcervantes)
Hello all, I’m working with PIC24FJ256GB410 in a PIM module for the EXPLORER16 development board. I’m using MPLAB X IDE 5.05 for code development and XC16 (v1.35) as compliler. My goal is to make an...
View ArticleIs Change Notify fundamentally broken? (SylviaElse)
In http://ww1.microchip.com/downloads/en/DeviceDoc/39711b.pdf on page 19, there is a block diagram of the working of the input change notification mechanism. While there are a pair of clocked latches...
View ArticlePIC24EP512GP - 60MIPS problem. (ice_man)
Hi, I try to set 60MIPS in PIC24EP512GP series and I dont know what I do wrong. I read Section 7. Oscilator for device, some information isn't clrearly for me. I will be grateful for any help. When I...
View ArticleProblem with printf() - use in PIC24EP512GP204 (XC16) causes reset... (ice_man)
Hi, I have problem with use printf() with PIC24EP512GP204 (XC16).Mcu will reset after use printf(). Watchdog is off. Device works with 60MIPS. Thanks for all help. // PIC24EP512GP204 Configuration Bit...
View ArticleExtended and Industrial Series Programming Time Difference (Emre_Kemsan)
Hi,I am using PIC24HJ256GP610A Industrial series and ICD3 programming device. I am programming this device nearly 5 second using ICD3. When I use PIC24HJ256GP610A extended series, programming time...
View ArticleBootloader adaptation from an old project (aliaskappa)
hello everybody,few years ago I developed a custom bootloader for some projects andI developped that using a PIC24fj128GC010.To do this i recovered from mla libraries the hid_boot_p24FJ128GC010.gld...
View ArticleTxCK selection (michael.mccormack@hefring.com)
I am designing a stepper motor interface using a timer and output compare to generate the pulses. I would like to use hardware to count the pulses and would therefore like to use the same pulse output...
View ArticleSCCP toggling. (scrungy)
I am using SCCP6 in triggered mode and 16 bit auto toggle, to generate pulses. I need the pulses however to be negative going, and it is not. I have configured RD11 to be output, and start high. In...
View ArticleMCC I2C Code (Danny Vigo)
I am following this tutorial for communicating with an MPU6050 gyroscope and accelerometer chip. I managed to set up the board correctly and I setup the chip using MCC, Now my problem is translating...
View ArticleECAN problem (reception without interrupt) - PIC24HJ256GP610 (kvnljs)
Hello everyone, I have a problem with the CAN module of my PIC24 HJ 256 GP 610. I am using the examples from the site (CE228_ECAN_FIFO, CE229_ECAN_RTR_120309, ...), sending and receiving works. The...
View ArticleBootloader with custom linker (Guilherme Marques)
Hello, I'm trying to understand how can i edit a bootloader linker to create a "go to" and acess bootloader page from my program. Firstly I used EZBL because it hasn't editable linker. "No .gld/.Id...
View ArticleHow can i create a correct linker/configuration bits for a bootloader without...
Hello, I'm trying to implements a serial bootloader that enter in boot mode from configuration menu and didn't reset the chip, because i would like to preserve the connection. I read several examples...
View ArticlePIC24FV16KM202 ADC Configuration (Svetlio141)
Hello. I am trying to configure the ADC on the PIC24FV16KM202 to read data.Unfortunately all I recieve are some random numbers that I get no matter if I have connected something to the pin or not.The...
View Article