moving from GB004 to GB002, remap pins (Dimitree)
hi everyone I'm moving a code from PIC24FJ64GB004 to PIC24FJ64GB002, since this one is 28pin, it has less pins so I need to remap UART2 RX and TX pins elsewhere, but I can't understand how should I do...
View ArticleUART transmit problems with the PIC24FJ256GB210 (mikenycz)
I have a program running that takes data stored in a char array and sends a message using the UART2 TX buffer... // Transmit message for (i=0;i<=12
View ArticlePIC24F16KA102 ASM example (Hartl192)
I want to start programming the PIC24F16KA102 in ASM. Does somebody know where I can find a short example code like a blinking LED or a tutorial? The most important for me is to learn how to set the...
View ArticleErase bootblock on PIC24FV32KA301 (g60luke)
Hi, I am looking to erase the bootblock (Address 0x0000 to 0x0200) on a PIC 24FV32KA301 I know that it cannot erase using normal Erase Rows commands as its protected. I have also tried setting NVMOP...
View ArticleUARTx MODE REGISTER, Unimplemented bit (User.06)
Target Chip: PIC24FJ256GB210 Manual: DS39975 Section 17 REGISTER 17-1: UxMODE: UARTx MODE REGISTER (Page 228 in my copy, year 2010, I think) In register U1MODE and U2MODE, bit #14 appears in the manual...
View ArticleSleep Mode affects on Peripherals (VolT)
PIC24FJ64GB004 Hello, In sleep mode of this pic the system clock source is shut down. For me this is an external HS crystal oscillator. It is stated that the processor will wake up on any interrupt...
View ArticleWatchdog timer in when using the debugger (mikenycz)
I am trying to set up the watchdog timer for the program I am running. I have put the code in to set the prescaler and postscaler and I have a clrwdt() statement in the main loop. When I compile and...
View ArticleDoze - selective interrups? (antarm)
I am looking into doze mode for my application, to conserve current while keeping up with external communication requirements. Does anyone know if there is a way to only use ROI for select interrupts,...
View ArticlePIC24FJ64GB002 supports 16bit ADC?! (Huya)
Hi I use MPLAB with CCSC and PIC24FJ64GB002. According to the datasheet, the internal ADC must be 10bit SAR structure. However, when I tried using 16bit ADC, it worked! Was it upgraded last year?? In
View Article3 SPI Slaves on a PIC with 2 SPI !!! (mavropoulosg)
Hi guys, This may be a silly question but I would like to connect a PIC24FJ64GB004, which has 2 SPI, to 3 slaves. As I can understand if I set the init with the PPS then I only have 2 SS1IN and SS2IN....
View ArticleConfiguring Ports (PIC24FJ128GA010) (sk8ermeb)
Hi, Thank you in advance for any help! I am fairly new with microchip products, and so I have download every bit of documentation I can find on the website, but I still cannot figure out exactly how to...
View ArticleHID Bootloader beginner questions (tone_crafter)
Hi All, I'm trying to get my head around the microchip USB HID bootloader. I have downloaded the Microchip Application Libraries v2012-07-18 and am using custom hardware with a PIC24FJ256GB106 device...
View ArticleTapping into the PIC24F Starter Kit 1 (TBayPic)
I've got to be missing something, but I am not sure how I can connect an analog signal to this board, or a frequency source to the CCP module.... I have a REV2 board. Thanks for any reply.
View ArticleInput capture PIC24FJ128GA010 Problem (AshiGupta)
Hello All, I am using PIC24FJ128GA010 controller to capture PWM input on 5 channels using Timer3. But i am getting worng values, i.e. my input signal is constant but values captured are fluctuating....
View ArticleTBLWTL Byte Mode (agoslash)
Hi everybody! I'm trying to program flash memory of my PIC24FV16KM202, but I don't know how to write in Byte Mode with TBLWTL instruction. This code should write 0xABCDEF at the address specified...
View ArticleHow to increase memory partition for user program memory for data storage?...
Hi, I am using EEPROM emulation technique using DEE Emulation 16-bit .c and DEE Emulation 16-bit.h for storing data in flash of PIC24FJ128GA310 micro-controller. I was able to store and read the data...
View Article24FJ256GB106 WEAK PULL-DOWN - was I using it incorrectly? (Spottymaldoon)
I wanted to use an internal weak pull-down to provide a ground for the emitter of a logic transistor which was connected directly to an input port (an optical isolator in fact). The port voltage read...
View ArticlePIC24F16KM202 (meits)
Anyone knows where to find the .INC and .GLD files for the 24F16KM family? Updated MPLAB IDE (not X) to 8.92. This version shows support in the device list. The installation however does not have the...
View ArticleBUY A TRUE FALSE **** ( forasia447@gmail.com ) DRIVING LICENCE / CARD ( ID) ,...
BUY A TRUE FALSE PASSPORT ( forasia447@gmail.com ) DRIVING LICENCE / CARD ( ID) , VISA false , fake birth. forasia447@gmail.com We are a team of professionals with years of experience in the...
View ArticlePWM with timer 4 (Halderha)
hello I have a Pic24fj64gb002 with 32 MHz time base. I will dim a led. The time base of the pwm is 208 kHz and the duty is 30%. The timer 4 is the timer for the pwm. On the pwm output I have no signal....
View Article