Android device communication with pic24F (swatvv)
hi all,Is that possible to connect android mobile or tablet(device) with pic24Fj256GB106 (Host) to access app in android device Through USB2.0.?..
View Articlers485, unable to receive (DRkidd22)
I have a program going and I can only transmit from the uControler, but can't receive anything. I've set the pps correctly and UART send out data fine. But when I try to send anything over the terminal...
View ArticleDeep Sleep when wake up where did it go? PIC24FJ64GA202 (haveaniceday)
My problem is while using WDT sleep ,the program is OK. while execute "RESET" after the WDT sleep , It reset and then going on. But while using DSWDT Deep Sleep. It will be low power consuming within...
View ArticleInterfacing a adafruit BME280 Breakboard to a PIC24FJ128GA204...
Hi, Has anybody successfully got this board to work with a PIC24FJ128GA204 see link. https://learn.adafruit.co...rature-sensor-breakout I realize this board is to designed for use with an Arduino...
View ArticleWhy was PIC24 not scaled up to 32bit? (picmadness)
I hope this is an OK place to ask this question: I have been looking at Pic32 architecture and comparing it to pic24/dsPIC33 and I think PIC24 is cleaner(though it lacks mmu and some other features). I...
View ArticleA minimalist RTOS for the PIC24 (Nicholas Lindan)
CoRTOS - The world's simplest RTOS (?) is available under GPL V3 (Update available, below) It is fully documented, with a 30 page pdf manual and fully commented source code. The intended audience...
View ArticleLocal variables not all displayed. (stman)
Hello. There is a bug in MPLABX IDE for 16 Bits microcontrollers : I am using a PIC24HJ and I noticed the following bug when using the debugger on Microstick II : Local variables do not appear when...
View ArticlePIC24FJ64GB002 to read USB Flashdrives (dmvillacorta)
Good morning! I would like to ask how to use the MAL USB libraries in order to read txt files from a USB using my PIC24FJ64GB002. I can't find a good beginners page for a step by step procedure in...
View ArticlePIC24FJ bootloader and flash programming problem (markq)
I have a problem where my bootloader is causing certain versions of my main load not to run but instead reset during its boot.I have been looking at this for several days and am kind of getting to my...
View ArticleConsumption of PIC24FJ1024GA606 in Idle mode is too high (Leonardo Morichelli)
Hi everybody, I have a problem with consumption of PIC24FJ1024GA606: As datasheet tolds, the consumption in LPRC clock mode, must be like follows: running: from 46 to 130 uA idle: from 30 to 110 uA My...
View ArticlePIC24EP512GU810 RTCC (yarthur)
I use the pic24ep512gu810, I want use sosc as rtcc clock source,sosc is connected to the external 32.768kHZ crystal. I according to the reference manual to set rtcc registers,but rtcc not running, the...
View ArticleQuirk with my otherwise functioning PWM Code (davez)
I have come up with the following, as my best? interpretation of the datasheet for a 24FV32KA304 PWM scheme, running at 4 Hz. (Using Timer 1, which is running off a 32.768 KHz crystal with a divide by...
View ArticleEZBL not compiling in latest MPLABx v3.61 and XC16 v1.31 (brada)
I've downloaded the latest EZBL (v1.01b) and I get all kinds of problems: CLEAN SUCCESSFUL (total time: 62ms) EZBL: Editing MakeFile-default.mk to enable linking with the Easy Bootloader for PIC24 and...
View ArticleNHD-3.5-320240MF and PIC24FJ128DA210 (fabianpi)
Hello I'm new working with these LCD and 16bit microcontrollers I'm interfacing with these LCD Display and I have a PIC24FJ128DA210 with a SST25VF040B I'm trying to follow these steps from the website:...
View ArticleHas anyone successfully used PIC24 hardware crc for MODBUS crc16? (forrestgk)
I have no problem creating coded crc16 functions which work fine, but have worked for hours to get the hardware crc working on the PIC24F32KA30x with no success. I don't need necessarily to know the...
View ArticleANALOG INPUT PIC24HJ32GP202 (electronicsArtist)
Hello I am trying to read an analog input from a potentiometer and save it in a variable myVal so far I some numbers read into myVal when i do step overs but they arent the figures on the potentiometer...
View ArticleI want to move data on LCD pin which connected on pin number 12,13 and 15...
I want to move data on LCD pin which connected on pin number 12,13 and 15 portB, Will given logic work for portB have pin 0 to 7 and then 12 to 15 pin. I am using p24fj64gc010 controller void...
View Articlei2c does not work in pic24HJ32GP304 micro (Quico)
Hello:I´m trying to start working with the i2c pins, but when I run the program below nothing happen (I check the SCL & SDA lines with logic analyzer but the lines remain in low level.I read...
View ArticleHow to program OTP in a PIC24F micro (longmax)
Hello,I'm looking for how to program OTP in a PIC24F micro. I could not find a note or a thread on the internet which shows how to write words on this memory of a PIC24F micro.Thanks a lot for any...
View ArticleMAL Host Bootloader processor configuration. (jnnewton)
I have the old MAL usb host bootloader working on my pic24fj128gb108 (128k prog mem) for short programs. But i need to move the line between the bootloader and application to allow for larger programs...
View Article
