Good evening.
I have connected a MCU PIC24FJ128GB204 to a delta sigma ADC on 3 wires + CS spi interface.
The MCU is master and ADC is slave.
When the ADC complete the conversion it pull down Data out line (idle level is high).
The ADC data out pin is ..
↧
PIC24FJ128GB204 DMA triggers (giuseppe83)
↧
PIC24FJ128GB202 - SOIC28: RP6 in datasheet stated to be on Pin3 AND Pin15 ??? (microhubbe)
PIC24FJ128GB202 in 28pin package Hi,unfortunately I already have the layout fixed and the finished PCBs in house... For my UART I just took al look at the pin table in the datasheet, if Pins RA0 und RA1 are remappable and indeed they are:RA0 (Pin2 on SOIC..
↧
↧
Where to Report FRM Errata ? (Abraxas)
Anyone know where we are to report FRM errata to ? Thanks...
↧
Access to hardware breakpoint from PIC program (marksullivan)
The subject line says it all ... Is there any way for the PIC24 itself to configure the hardware breakpoint? And, if it could, would some kind of operating system be able to gain control when it fires? Like maybe it freezes up and the WDT fires?..
↧
internal RTCC in PIC24f, Alarm setting problem (Maurya)
Hi,I am using inbuilt rtcc in pic24fj126ga310. I want to get the current time and set the alarm after 2 hour of the current time. And the alarm interval is not same as given by ALCFGRPTbits.AMASK with different setting. Alarm required some times at 10 min..
↧
↧
Data EEPROM Access on PIC24FV32KA304 (kathappan)
Hi all, I am using PIC24FV32KA304 and MPLAB X IDE (v3.30) along with XC 16 (v1.26). In in PIC24FV32KA304, the data EEPROM is mapped to the memory address from 7FFE00h to 7FFFFFh(256 words). The EEPROM operations can be done using NVMCON, NVMKEY and NVMADR..
↧
PIC24 Using SPI on XIDE 3.30 and Code Configurator: Where To Begin ?? (Abraxas)
Greetings I'm trying to get a very simple project going that reads a thermocouple via a MAX31855. I won't worry about the display part yet and hope to just read it using LEDs or something. All I've been able to figure out thus far is that I should make my..
↧
Flash Drive cannot enumerate problem on PIC24FJ128DA106(USB HOST) (Tamil1802)
problem on "USB_CANNOT_ENUMERATE" @ PIC24FJ128DA106(USB HOST ONLY)
I am doing project on Pendrive has to read by PIC24FJ128DA106(USB HOST)
i am using Microchip Library App (msd_simple_demo),in that i am configuring for pic24fj128da106(from pic24j256da..
↧
PIC24F08KL200 How to set pins to digital I/O (RBanks)
Cannot find any reference to using the ANSx registers to set I/O pins to digital outputs. Other devices use AD1PCFG register but this does not exist in this part's p24f08kl200.h file. These registers are not given in the device's datasheet. Anyone know ho..
↧
↧
Bootloader PIC24 EP (jg_ee)
Hello, I am trying to get a bootloader and application working together on the PIC24EP512GP806. I am having some issues getting my linkers sorted out, but the above reference Code Example from the product page does not appear to have any sort of applicati..
↧
Eeprom issue with Explorer 16 board and PIC24FJ128GA010 (negimarules)
I am trying to use the Eeprom chip (25LC256) on the board to store my variable values after power is cut out. I did some research and read about how to use Eeprom in general. However, I was not able to make it work. Every time I wrote to it and read back,..
↧
PIC24FJ128GA202 SPI settings problems (mgedion)
Hello, I am trying to port my code from PIC24FJ64GA002 to PIC24FJ128GA202.Unfortunately I cannot set up the SPI settings. I read the datasheet, fount out that there are two buffers (SPI2BUFL and SPI2BUFH) instead of one, but did not find any App notes how..
↧
PIC24FJ256GA406 RTCC battery backup not working (maarten a)
Dear, I'm trying to use the RTCC with an external battery, unfortunately the RTCC resets when the power is removed. I measured the backup battery on the VBAT pin, it holds a strong 3.1V. I use an external oscillator which also continues to work on battery..
↧
↧
pic24fj64gb002.usb connections and transfer (dinol)
I am new to mplab x ide. I am using pic24fj64gb002 controller. I have downloaed the libraries from . But I dont knOw how to add the files and use it. I want to store some datas and send through USB in a continous manner...
↧
PIC24FJ256GA110 UART with DMA (tuxx)
Hello, first of al i searched now for hours for a simple UART/DMA example source, it seems that there is no documentation at all.PIC24F FRM Section 54. Shows some easy examples for DMA Transfers from memory to Memory, but does not mention UART. I tried to..
↧
PIC24F04KA200 no response using pickit 2 (Toffeeflavour)
Hello all,
I am the noob, I know right.
So here is the thing, I created a program in MPLAB X IDE 3.30 and downloaded the hex file to the chip using pickit 2 and the standalone pickit 2 program version 2.61. The PIC doesn't respond while the simulator ..
↧
ReadID Fail with M240021 + Pickit3 (unicondor)
Hi All,I just bayed the M240021 (pic24fj256gb210 PIM for explorer 16) but I would want to know if I can directly connect my pickit3 with M240021 without using the Explorer 16. I tried several times to read the ID, But I always receive error (read id = 0x0..
↧
↧
New To PIC24 Setup (Terrere)
I am trying to start a small IR project with a PIC24F16KL402. I plan to expand to a larger project as I learn with it. My intended goal is to set up a laser tag system that communicates via IR pulse messages. I'm having a bit of trouble trying to figure o..
↧
Can we use the PIC24FJ256DA210 code for PIC24FJ128DA106 uC( both are same family)? (Tamil1802)
i am configuring MSD_SIMPLE_DEMO project code(PIC24FJ256DA210) to PIC24FJ128DA106.I am changing the configuration option according to this hardware(pic24fj128da106). This code will work or not?...
↧
PIC24FJ64GA004 Memory Issue (harini04)
Hello everyone, Please find the attached images and the below description on it and give the solution on this immediately. Case 1 : For an array of 2000 data on 2 Variables declared Locally, I am able to get the dataCase 2 : For an array of 4000 data on 2..
↧